OUR ETTER ART PREMIUM SILICONE

3D Silicone Mould: Your Transparent Mould for That Special Touch The products in our Etter Art Shop are meticulously tested by Stefanie Etter herself to ensure the highest quality, and this silicone mould is no exception.   Applications of the 3D Silicone Mould This versatile 3D mould is perfect for filling with resin, hydroflow, and AQUA CAST. You can create your own unique pieces, whether as a jewellery box, candle holder, storage container, gift box, sweet box, or even a flower pot—let your imagination run wild!   Special Features of the 3D Silicone Mould • High-quality silicone  • Exceptional flexibility  • Intricate detail  • Non-flammable  • Skin-safe and non-toxic  • Durable  • Recyclable    Important Care Instructions To enhance the durability of your moulds, avoid using sharp objects or exposing them to excessive heat. Do not store the moulds upside down, as this can cause the base to bulge. Before use, rinse the mould with clean water, remove any dust, degrease, and ensure it is placed flat on your work Surface.   Dimensions of the 3D Silicone Mould • Base:Outer diameter: 9.5 cm; Inner diameter: 7.6 cm; Height: 6.5 cm • Lid: Diameter: 9.0 cm; Height: 2.5 cm 

Silikonform in 3D: deine transparente Form für mit dem besonderen Etwas Die Produkte bei uns im Etter-Art-Shop werden eigenhändig und mit viel Hingabe von Stefanie Etter getestet und auf ihre hohe Qualität überprüft. Das gilt auch für diese Silikonform.   Anwendungsmöglichkeiten Silikonform 3D Diese 3D Form eignet sich hervorragend zum Befüllen mit Resin, hydroflow und AQUA CAST. Du kannst damit deine eigenen Kunstwerke kreieren. Ob als Schmuckdose, Kerzendose, Aufbewahrungsbox, Geschenkbox, Süßigkeiten Box oder auch als Blumentopf - deiner Fantasie sind keine Grenzen gesetzt.   Besonderheiten der Silikonform 3D Hochwertiges Silikon Hohe Flexibilität Detailgetreu Nicht entflammbar Nicht schädlich bei Kontakt mit der Haut Langlebig Recyclebar   Darauf solltest du achten! Um die Haltbarkeit der Formen zu erhöhen, solltest du nicht mit spitzen Gegenständen oder zu großer Hitze arbeiten. Die Formen sollten nicht auf der Kehrseite aufbewahrt werden, da sich sonst der Unterboden nach oben wölben kann. Vor dem Gebrauch mit klarem Wasser ausspülen, enstauben, entfetten und eben auf der Arbeitsfläche platzieren.   Maße Silikonform 3D Siehe Artikelbilder. Entdecke weiter Formen hier:

THE ETTER ART SILICONE MOLDS IN 8 DIFFERENT VERSIONS That's them. Our Etter Art silicone molds in 8 different designs are high-quality silicone molds that are produced in-house with our PREMIUM SILICONE SOFT ROSÉ 22. They can. The Etter Art silicone molds are ideal for filling with resin, concrete, hydroflow or similar. There are no limits to your design. You can work with colors but also haptic objects and integrate them into your form. Particularities. • Own production. • True to detail, sophisticated, hard-wearing and elastic. • Suitable for making coasters, trays, candle holders, baking tins and more. • Solvent-free. • Food quality. • Non-corrosive. • Non-flammable. • Not harmful in contact with Skin. You should pay attention to that. To increase the durability of the molds, you should not work with pointed objects or excessive heat. The molds should not be stored on the reverse side, otherwise the sub-floor can bulge upwards. Rinse with clear water before use, dust off, degrease and place flat on the work surface. Your forms. • Square • Circular • Circular with scalloped edges • Hexagon • Soap Dish • Triangle (Small/Big) • Geode

OUR ETTER ART SILICONE LIGHT GRAY 32 That's it. Our Etter Art PREMIUM SILICONE LIGHT GRAY 32 is a silicone rubber consisting of two components, base and catalyst. It is easy to process, has a low viscosity and very good flowability. It can. The Etter Art PREMIUM SILICONE LIGHT GRAY 32 has a high level of detail in the reproduction. It hardens without reaction heat to form a durable, elastomeric plastic. In addition, it is extremely tear-resistant and flexible in use. After the hardening process, it can be easily removed from the negative model thanks to its excellent non-stick effect. That's what it's for. The Etter Art PREMIUM SILICONE LIGHT GRAY 32 is suitable for impressions that have to be detailed, demanding, durable and elastic. It is particularly suitable for imprints of all kinds, such as coasters, trays, candle holders, baking tins and much more. You can also use it for casting resin, soap casting, plaster or concrete. The Etter Art PREMIUM SILICONE LIGHT GRAY 32 is also suitable for manual or machine processing. Particularities. • Addition curing. • Hardness: Shore A 32 (after 24 hours). • Heat resistant up to 180 °C. • Frost-resistant down to at least -45 °C. • Can be stored unopened for up to one and a half years. • Processing at room temperature around 15 °C. • Minimal shrinkage below 0.1%. • Viscosity of 5,300 mPa. • Tear strength up to 20.8 KN/m. • Resistant up to 5.0 N/mm² • Solvent-free. • Food quality. • Non-toxic. • Non-flammable. • Non-corrosive. • Not harmful in contact with Skin. Measuring, mixing and processing PREMIUM SILICONE LIGHT GRAY 32 1.) Base and catalyst of PREMIUM SILICONE LIGHT GRAY 32 are mixed by weight 1:1. Place the components in a suitable mixing cup. 2.) Stir the measured amount in the mixing cup. Stir slowly and thoroughly for 2-3 minutes; also on the bottom and the edges of the mixing cup until a streak-free and even gray tone is achieved. 3.) Your mixture is ready and you now have 9-10 minutes to process the silicone. After that it becomes too thick and begins to harden. 4.) You have previously prepared your casting mold, which means: It is dusted, degreased and lying flat on your work surface. Pour the silicone from a great height into your mold in a narrow stream. The great height ensures that the result is as bubble-free as possible. 5.) Protect your form from dust or other foreign objects by working in an environment that is as dust-free as possible. The curing time is one hour at a room temperature of 23 °C. The silicone can be removed from the mold after 3 Hours.

OUR ETTER ART PREMIUM SILICONE SOFT ROSÉ 22 That's it. Our Etter Art PREMIUM SILICONE SOFT ROSÉ 22 is a silicone rubber consisting of two components, base and catalyst. It is easy to process, has a low viscosity and very good flowability. It can. The Etter Art PREMIUM SILICONE SOFT ROSÉ 22 has a highly detailed reproduction. It hardens without reaction heat to form a durable, elastomeric plastic. In addition, it is extremely tear-resistant and flexible in use. After the hardening process, it can be easily removed from the negative model thanks to its excellent non-stick effect. That's what it's for. The Etter Art PREMIUM SILICONE SOFT ROSÉ 22 is suitable for impressions that have to be detailed, demanding, durable and elastic. It is particularly suitable for imprints of all kinds, such as coasters, trays, candle holders, baking tins and much more. You can also use it for casting resin, soap casting, plaster or concrete. The Etter Art PREMIUM SILICONE SOFT ROSÉ 22 is also suitable for manual or machine processing. Particularities. • Addition curing. • Hardness: Shore A 22 (after 24 hours). • Heat resistant up to 180 °C. • Frost-resistant down to at least -45 °C. • Can be stored unopened for up to two years. • Processing at room temperature around 15 °C. • Minimal shrinkage below 0.1%. • Viscosity of 3,260 mPa. • Tear strength up to 24.0 KN/m. • Resistant up to 5.0 N/mm² • Solvent-free. • Food quality. • Non-toxic. • Non-flammable. • Non-corrosive. • Not harmful in contact with Skin. Measuring, mixing and processing PREMIUM SILICONE SOFT ROSÉ 22 1.) Base and catalyst of PREMIUM SILICONE SOFT ROSÉ 22 are mixed by weight 1:1. Place the components in a suitable mixing cup. 2.) Stir the measured amount in the mixing cup. Stir slowly and thoroughly for 2-3 minutes; also on the bottom and the edges of the mixing cup until a streak-free and even rosé tone is achieved. 3.) Your mixture is ready and you now have 7-8 minutes to process the silicone. After that it becomes too thick and begins to harden. 4.) You have previously prepared your casting mold, which means: It is dusted, degreased and lying flat on your work surface. Pour the silicone from a great height into your mold in a narrow stream. The great height ensures that the result is as bubble-free as possible. 5.) Protect your form from dust or other foreign objects by working in an environment that is as dust-free as possible. The curing time is one hour at a room temperature of 23 °C. The silicone can be removed from the mold after 3 Hours.